The article following next on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is fairly fascinating. You should give it a look.
Installing a bathtub isn't precisely rocket science, but it does require strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old bathtub is readily available, the job can relocate rapidly; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to leave the old tub and also set in the new one. See to it you have actually qualified yourself for the work and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly assist you install a new tub in your washroom if you have actually already gotten a brand-new tub and do not need to alter the setup of your previous water system pipelines.
Your devices as well as product checklist must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of removing the existing taps can be quite bothersome as a result of the restricted gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washers remain in area in between the faucet and also the sink. Secure the tap in position with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the tap ends initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Using the two wood boards under its feet, put the bathtub in the called for placement. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water as well as check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the bath tub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the tub should wait up until the tub has actually been used a minimum of once as this will certainly resolve it into its final setting.
Planning for the Installation
First of all, the supporting framework supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to avoid pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, causing complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that entry on A Step-by-Step Guide to Installing a Bathtub while doing a search on the web. Sharing is caring. Helping people is fun. Thanks for taking the time to read it.
Need assistance? Call.